Shop
BMS – 7S – 24V 20A
In stock
- Use top quality (A-level) protective integrated circuit IC, from the solution of Seiko of Japan.
- Strong load ability, constant discharge current 10A/25/35A/45A/60A , use high voltage resistance, low inner
- resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection
- Function is very reliable. Long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. The consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal Coating.
BMS -3S-HX-3S-01- ORG CHIP
In stock
Note:
- The battery will heat when using it, it means the battery does not apply, please don’t keep using because the battery will be damaged soon.
- The protection board can not be used for lithium iron phosphate battery, hernia lamp, hand drill battery pack, electric fish machine battery pack, electric bicycle battery pack, children’s car battery, 775 (4A)motor, 1W fish eye LED light!
Precautions:
- Please strictly follow the wiring 0V (B -), 3.7V (B1), 7.4V (B2), 11.1V (B +), do not deliberately short circuit.
- Please charge after connecting the line, then it will have output.
- When connecting three groups of batteries, please ensure that the voltage of each group of batteries, if not the same, please fill each battery separately and then use it in series. The discharge test, the voltage drops quickly.
BMS 10S 40A NMC
In stock
This BMS offers below mentioned protection of utmost importance.
- Overcharge Protection
- Temperature Sensor Protection
- Over discharge Protection
- Short Circuit Protection
- Overcurrent Protection
- Cell Balancing Function
BMS 13S 40A NMC
In stock
- State of charge calculations.
- Cell over-voltage and under-voltage protection.
- Intelligent battery balancing (passive).
- Fully sealed waterproof technology, with waterproof, dustproof, shockproof, anti-squeezing, and other protective functions.
BMS 3S – 10A
In stock
- Three series of lithium battery protection board.
- Automatically cancel protection after protection conditions restore.
- With the function of overcharge protection, over discharge protection, short circuit protection, over-current protection.
- Suitable for lithium battery pack of 11.1V, 12V, 12.6V.
- Quiescent current < 30uA, so power consumption is small.
BMS 3S -20A
In stock
- Overcharging and Over Discharging Protection
- Short circuit protection: Yes
- Applicable assembly: Nominal 4.5V Batteries / 3 strings.
BMS NMC 7S 20A
In stock
This Lithium ion battery protection PCB protect single Lithium ion batteries and it has 20A continuous current. It is suitable for electric drills,motors, or aircraft models which require heavy current load.
BN100S8 SPADE NICKEL PLATED LONG LIFE BIT FOR SOLDRON 100W SOLDERING IRON
In stock
- SOLDRON 100W SPADE LONG LIFE BIT FOR HEAVY DUTY SOLDERING IRON.
- TO BE USED WITH THE SOLDRON 100W SOLDERING IRON TIP .
- 8MM SPADE NICKEL PLATED TIP .
- SLIDE ON TECHNOLOGY FOR TIP REPLACEMENT.
BN25N3 25 WATT NICKEL PLATED NEEDLE BIT FOR SOLDRON 25W SOLDERING IRON
In stock
- Power rating is 25W
- Plated with Nickel
- Durable and Long Life Total Length: 75 mm.
- Slide-on technology for tip replacement.
BN25S3 NICKEL PLATED SPADE 3MM BIT FOR 25W SOLDERING IRON
In stock
- Power rating is 25W
- Plated with Nickel
- Durable and Long Life Total Length: 75 mm.
- Slide-on technology for tip replacement.
BN35S3 SPADE NICKEL PLATED BIT FOR 35W SOLDERING IRON
In stock
- SOLDRON 35WATTAGE NICKEL PLATED BIT .
- TO BE USED WITH SOLDRON 35W SOLDERING IRON.
- SLIDE ON TECHNOLOGY FORTIP REPLACEMENT.
- IDEALLY TO BE USED WITH SOLDERING STATIONS AS ITS VOLTAGE SENSITIVE WILL BE DAMAGED.
- COMES WITH AN ISOLATED ELEMENT AND LONG LIFE ALUMINIUM COATED TIP .
BN50S5 SPADE NICKEL PLATED BIT FOR SOLDRON 50W SOLDERING IRON
In stock
- 50W 75MM length bit ( soldering iron tip ) is hight quality soldering iron tip .
- IT CAN BE USED WITH ANY STANDARD 50W SOLDERING IRON.
- HIGH-QUALITY ORIGINAL SOLDERING IRON BIT.
- SLIDE ON TECHNOLOGY FOR TIP REPLACEMENT.
- THIS IS 50W NICKLE PLATED SPADE 3MM BIT WITH FLAT SPADE TIP.
BN75S6 SPADE NICKEL PLATED LONG LIFE BIT FOR SOLDRON 75W SOLDERING IRON
In stock
Soldron 75w Spade Premium Grade Long Life Bit for Heavy Duty Soldering.
To be used with the Soldron 75W Soldering Iron.
BO Motor L Clamps for mounting BO Motor
In stock
It is a Mounting Clamp for BO Motor. It is made from MS steel and has a thickness of 1mm.
Uses these clamps to mount your BO Motors. It comes with holes which align onto the motor holes and holes for mounting the clamp onto a chassis.
BO Motor Single Shaft DC Motor
In stock
Small shaft with matching wheels gives an optimized design for your application or robot. Mounting holes on the body & light weight makes it suitable for in-circuit placement. This motor can be used with 69mm Diameter Wheel for Plastic Gear Motors.
It is an alternative to our metal gear DC motors. It comes with an operating voltage of 3-12V and is perfect for building small and medium robots.
The motor is ideal for DIY enthusiasts. This motor set is inexpensive, small, easy to install, and ideally suited for use in a mobile robot car. They are commonly used in our 2WD platforms.
BO Red Wheel
In stock
- THESE ARE THE RED BO MOTOR WHEELS
- THESE WHEELS ARE OF GOOD QUALITY.
- THE DIAMETER OF WHEEL IS 70MM ( 7CM )
- THE WIDTH OF WHEEL IS 10MM( 1CM )
- SCREWS CAN BE FITTED INTO THE AXLE SOCKET MOUNTED FROM THE FRONT FOR K
BO WHEEL IMPORTED
In stock
Features of BO Wheel:
- The car hub is reinforced nylon, very sturdy.
- The tire is made of soft rubber for a non-slip effect.
- Good load capacity and greater ability to grip
- Robot Wheel Material: Plastic + Rubber
BO WHEEL PULLEY
In stock
This is a plastic pulley. These Plastic pulleys can be used to drive wheels or other pulleys with a belt. This Plastic pulley is perfect for DIY Science Projects and Experiments. It comes with a 6mm shaft/bore which makes it compatible with our wide range of DC Motors, 6mm Shafts, Couplers, Gears, etc.